GRC构件在建筑行业的地位是很重要的。咱们经常在古典建筑风格的建筑物上都会看到GRC构件。
山东GRC构件虽然具有防潮、耐腐蚀性，可是，为了添加其使用寿命，也需求咱们进行护理的。
GRC components play an important role in the construction industry. We often see GRC components on buildings with classical architectural style. Although GRC components have moisture-proof and corrosion resistance, we also need to take care of them in order to increase their service life.
1、GRC构件避免沾上灰尘和污渍：可以用吸尘器来清洁砂岩背景墙而且要确保吸尘器是软毛刷，因为硬设备可能会刮伤砂岩。
1. Avoid dust and stains on GRC components: use a vacuum cleaner to clean the sandstone background wall and ensure that the vacuum cleaner is a soft brush, because hard equipment may scratch the sandstone.
2、安装好后尽快密封：密封口可以充当砂岩背景墙的保护层，防止灰尘和污渍的进入以及砂岩内的水分蒸发，因为它和空气中的化学物质发生反应可能会损坏砂岩背景墙。
2. Seal as soon as possible after installation: the sealing opening can serve as the protective layer of the sandstone background wall to prevent the entry of dust and stains and the evaporation of water in the sandstone, because it may damage the sandstone background wall if it reacts with chemical substances in the air.
3、GRC构件不要接触油污：因为油或污垢会导致砂岩背景墙染色，如果接触到了应该尽快清理避免被砂岩吸收。
3. GRC components shall not be exposed to oil stain: because oil or dirt will lead to the staining of sandstone background wall, if it is exposed, it shall be cleaned as soon as possible to avoid being absorbed by sandstone.
4、避免使用瓷砖清洗剂清洁：瓷砖清洗剂会使墙壁瓷砖褪色应该用干净的软布和温水，经常擦拭可以防止有害化学物质的沉积。
4. Avoid the use of ceramic tile cleaning agent: ceramic tile cleaning agent will make the wall tiles fade. Clean soft cloth and warm water should be used. Frequent wiping can prevent the deposition of harmful chemicals.
GRC构件的实际养护过程中，需要分为以下几个阶段来进行：
The actual curing process of GRC components needs to be divided into the following stages:
1、修饰之后，通常需要采用洁净而且的聚乙烯薄膜来将模具包住，以放置GRC构件中的水分受到蒸发和风的影响，同时也有助于保持水化热，在养护的初期应保证GRC构件能够拥有足够的强度，使其在脱模与搬运的过程中不会受到损伤。
1. After finishing, it is usually necessary to wrap the mold with clean polyethylene film to place the moisture in the GRC component affected by evaporation and wind, which also helps to maintain the heat of hydration. At the initial stage of curing, it is necessary to ensure that the GRC component can have sufficient strength, so that it will not be damaged during demoulding and handling.
2、为脱模之后的GRC构件继续进行保护，以免其会受到光照、风雨空气低湿度的影响，一般情况下仍采用塑料薄膜将GRC构建包裹住，以免受到阳光的直接照射，通过喷湿雾也可以保持局部的湿度。
2. In order to protect GRC components after demoulding from the impact of light and low humidity of wind, rain and air, plastic film is generally used to wrap GRC components to avoid direct sunlight, and local humidity can also be maintained by spraying wet fog.
3、在GRC构件的存放和使用过程中，由于其周围环境与养护阶段存在着明显的差异，因此也是需要进行一定的养护操作的，此时可以采用一些简单的方式来保证其在存放过程中不会受到阳光的直接照射。
3. During the storage and use of GRC components, due to the obvious difference between the surrounding environment and the curing stage, certain maintenance operations are also required. At this time, some simple methods can be used to ensure that GRC components will not be directly exposed to the sun during storage.
I believe that through reading this article, you have a new understanding and understanding of what should be paid attention to in the use and care of GRC components. If you have any questions, please go to our official website http://www.aswjc.com Check, thank you for your reading and support.
