山东GRC构件具有总量小，强度高、抗冻融性好、可塑性强、装饰造型丰富多样的优点，广泛的用于新建外装饰、旧楼改造、外墙造型挂板、园林配景。下面来讲讲有关GRC构件的行业小知识吧。

Shandong GRC components have the advantages of small total amount, high strength, good frost and thaw resistance, strong plasticity and rich and diverse decorative shapes. They are widely used for new external decoration, old building renovation, external wall modeling hanging plate and garden landscape. Let's talk about the industry knowledge of GRC components.

GRC制品及其连接件应具有足够的强度、刚度及稳定性。GRC制品工程在进行结构设计计算时，应作为非结构构件，不参与主体结构承载分析，但应按相关的规范规定，进行合理的构件设计，避免对主体结构的不利影响。GRC构件

GRC products and their connectors shall have sufficient strength, rigidity and stability. GRC products engineering shall be regarded as non structural members during structural design and calculation, and shall not participate in the bearing analysis of the main structure. However, reasonable member design shall be carried out according to relevant specifications to avoid adverse impact on the main structure. GRC component

根据破坏后的严重程度，GRC制品工程划分为三个等级。设计时应根据具体情况，按照有关的规定，选用相应的等级。

According to the severity of damage, GRC product engineering is divided into three safety levels. During design, corresponding safety levels shall be selected according to specific conditions and relevant regulations.

1.GRC一般装饰制品结构设计时除应进行制品本身的强度及刚度验算外，还应对连接部位进行承载力验算，如锚固强度、局部承压等。

1. In the structural design of GRC general decorative products, in addition to checking the strength and rigidity of the products themselves, the bearing capacity of the connecting parts shall also be checked, such as anchorage strength and local bearing capacity.

2.详细计算方法应参照有关规定执行。

2. The detailed calculation method shall refer to relevant regulations.

3.GRC外墙板的结构设计：GRC外墙板结构设计时除应进行GRC外墙板的强度、刚度验算和与背负式钢架连接处的承载力验算外，还应对背负式钢架本身进行各杆件的强度刚度验算：对背负式钢架与主体结构的连接也应进行承载力验算。

3. Structural design of GRC exterior wall panel: in the structural design of GRC exterior wall panel, in addition to the strength and rigidity checking calculation of GRC exterior wall panel and the bearing capacity checking calculation of the connection with the piggyback steel frame, the strength and rigidity checking calculation of each member of the piggyback steel frame shall also be carried out: the bearing capacity checking calculation shall also be carried out for the connection between the piggyback steel frame and the main structure.

GRC构件的安装要求

Installation requirements for GRC components

1、构件安装要求横向平整、竖向垂直、整体上线、花饰组对完整、曲线圆滑流畅，构件表面无缺损。

1. The installation of components shall be horizontal and vertical, the overall upper line, the floral assembly shall be complete, the curve shall be smooth and smooth, and the component surface shall be free of defects.

2、构件安装节点对位准确，防止因埋件错位导致构件强扭就位，产生安装应力而日久变形。

2. The alignment of the component installation nodes is accurate, so as to prevent the strong torsion of the component in place due to the dislocation of the embedded parts, and the installation stress and long-term deformation.

3、构件连接点须连接到位，不得遗漏。螺栓连接须带紧拧靠。

3. The connection points of components must be connected in place without omission. Bolt connection must be tightened.

4、构件接头顺畅，接缝小于10mm。

4. The joints of components shall be smooth and the joints shall be less than 10mm.

5、竖向构件应避免将上部构件层层叠压在底部构件上，而应将每一截构件单独悬挂安装在墙体上。

5. The vertical members shall avoid stacking the upper members on the bottom members layer by layer, and each section of members shall be hung and installed on the wall separately.

6、构件安装完毕，应自上而下将表面的灰尘和污渍清扫干净，勾缝饱满、打磨平整。

6. After the components are installed, the dust and dirt on the surface shall be cleaned from top to bottom, and the joints shall be full and polished.

GRC建筑装饰构件的种类、规格、图案，以人为本。构件按照业主的要求设计制作而成，尽管品种规格不一，但在生产过程中全部埋入安装构件，施工时膨胀螺栓固定，省时、省工、省力，降低成本，减少费用。有需求就来我们网站http://www.aswjc.com咨询。

The types, specifications and patterns of GRC building decoration components are people-oriented. The components are designed and manufactured according to the requirements of the owner. Although the varieties and specifications are different, all the components are embedded and installed in the production process. The expansion bolts are fixed during construction, which saves time, labor and labor, and reduces costs and expenses. Come to our website if you need http://www.aswjc.com consulting service