在设计假山的时候,可以利用GRC构件制作,利用GRC的好处是,可以真实度更高,纹理更加清晰,可以适用于很多复杂的环境下,减少工程吊装的时间,效果更真实,那么大家知道如何用GRC制作假山吗?如何适应环境呢?接下来我们一起来看看吧!
When designing rockery, GRC components can be used to make rockery. The advantage of using GrC is that it can be more realistic, the texture is clearer, and it can be applied to many complex environments. It can reduce the time of engineering hoisting, and the effect is more realistic. So do you know how to make rockery with GRC? How to adapt to the environment? Let's take a look next!
grc假山模块制作假山屋的过程如下:1、制作grc假山模具;2、制造grc假山模块;3、在假山房的墙壁上焊接承重架;4、在钢架上焊接假山模块;5、接合;6、着色;7、护色。
The manufacturing process of GRC rockery module rockery house is as follows: 1. Manufacturing GRC rockery mold; 2. Manufacturing GRC rockery module; 3. Welding the bearing frame on the wall of the rockery house; 4. Welding the rockery module on the steel frame; 5. Jointing; 6. Coloring; 7. Color protection.
1、制作grc假山房屋模具:选择真山要仿的部分,用硅胶反复涂抹,直到厚度达到2 cm以上。硅胶达到硬度后,用石膏在硅胶上做一个硬模具。
1. Making GRC rockery house mold: first, select the part of the real mountain to be imitated, and apply it repeatedly with silica gel until the thickness reaches more than 2 cm. After the hardness of the silica gel is reached, plaster is used to make a hard mold on the silica gel.
2、制造GRC构件假山模块:用制作好的模具转动玻璃钢假山模块,将石膏硬模放在底部,硅胶模放在顶部,先在硅胶模内铺一层快硬硫铝酸盐水泥,然后铺上玻璃网格布,再铺上2层水泥或直接用喷浆机喷,厚度约3厘米,长宽约1、5米。
2. Manufacturing GRC components rockery module: use the made mold to rotate the glass fiber reinforced plastic rockery module, put the gypsum hard mold on the bottom and the silica gel mold on the top, first lay a layer of fast hardening sulphoaluminate cement in the silica gel mold, then lay the glass mesh cloth, and then lay two layers of cement or spray directly with the shotcreting machine, with the thickness of about 3cm, the length and width of about 1m or 5m.
3、在假山房的墙壁上焊接承重架:在要建假山的房子墙上打洞,间距1m左右。安装膨胀螺栓,焊接5厘米角钢。焊接后,做防锈处理。焊接辅助架应与效果图纸结合,高低位置不应颠倒。
3. Weld the load-bearing frame on the wall of the rockery house: make holes on the wall of the house to be built with a spacing of about 1m. Install expansion bolts and weld 5cm angle steel. After welding, do antirust treatment. The welding auxiliary frame shall be combined with the effect drawing, and the height position shall not be reversed.
4、在钢架上焊接假山模块:焊接grc假山模块时,注意推迟相邻两个grc假山模块之间的纹理。将grc假山模块与水冲刷线焊接时,水冲刷线应尽可能水平。尽量把接口定位在内角,因为内角的接口比较好处理。
4. Welding rockery module on steel frame: when welding GRC rockery module, pay attention to delay the texture between two adjacent GRC rockery modules. When the GRC rockery module is welded with the water erosion line, the water erosion line should be as horizontal as possible. Try to locate the interface in the inner corner, because the interface in the inner corner is easier to handle.
5、接合:要特别注意指向假山屋,因为指向位置的假山皮比较粗糙,需要在指向时手动重新纹理化两块假山皮。
5. Joint: special attention should be paid to pointing to the rockery house, because the rockery skin pointing to the position is rough, so it is necessary to manually re texture the two rockery skins when pointing.
6、上色:grc假山房方法多次上色,就像水泥直塑假山房方法一样。
6. Coloring: the GRC rockery house method is colored many times, just like the cement direct molding rockery house method.
7、护色:粉刷后涂上一层护色剂,可以保护假山屋的颜色不受外界影响,减缓褪色。
7. Color protection: after painting, apply a layer of color protection agent to protect the color of the rockery house from external influence and slow down fading.
利用GRC构件产品制作假山的流程主要是制作grc假山模具、制造grc假山模块、在假山房的墙壁上焊接承重架、在钢架上焊接假山模块、接合、着色、护色等7大步骤,这7个步骤是重要的施工环节,在施工的时候,千万不能忽视,应严格按照标准进行施工,保证假山效果更真实。
The process of making rockery with GRC component products mainly includes seven steps: making GRC rockery mold, making GRC rockery module, welding load-bearing frame on the wall of rockery house, welding rockery module on steel frame, jointing, coloring and color protection. These seven steps are important construction links, which should not be ignored during construction. Construction should be carried out in strict accordance with standards to ensure rockery efficiency The results are more real.