GRC构件是以耐碱玻璃纤维作增强材，低碱度水泥为胶结材并掺入适宜集料构成基材，通过喷射、立模浇注、挤出、流浆等生产工艺而制成的轻质、高强高韧、多功能的新型无机复合材料。与混凝土同等性能及寿命，是一种可再生循环利用的绿色建筑材料。GRC构件形态优美，装饰在各种大众小型建筑上，给建筑增添了美感。下面给大家介绍一下GRC构件生产前准备有哪些？
GRC component is a new type of inorganic composite material with light weight, high strength, high toughness and multi-function, which is made of alkali resistant glass fiber as reinforcement, low alkalinity cement as cementitious material and suitable aggregate as base material through spraying, formwork pouring, extrusion, slurry flow and other production processes. With the same performance and service life as concrete, it is a renewable and recycled green building material. GRC components have beautiful shapes and are decorated on various public small buildings, adding beauty to the building. Now let's introduce the preparations for GRC components before production?
一、GRC构件产品打样确认
1、 GRC component product proofing confirmation
根据甲方提供的效果图或实物样品，样品应注意以下几点：
According to the renderings or physical samples provided by Party A, the samples should pay attention to the following points:
1、表面效果符合甲方要求。
1. The surface effect meets the requirements of Party A.
2、样品颜色符合甲方要求。
2. The color of the sample meets the requirements of Party A.
3、应一次抽取两个样本。样品制成后，销售人员应对其进行一次检查，以查看其是否合格。检查时需要注意检查表面效果，色差，是否存在毛孔，是否龟裂等，并再将模板照片发送给甲方之前确认样品正确。甲方确认甲方将发送确认后将样本打包交给甲方的设计师签名。设计师将为甲方签字，另一名将签字退还给公司以取得大宗商品。
3. Two samples should be taken at a time. After the sample is made, the salesperson should first check it to see whether it is qualified. During the inspection, it is necessary to check the surface effect, color difference, pores, cracks, etc., and then confirm that the samples are correct before sending the template photos to Party A. Party A confirms that Party A will send the samples to Party A's designer for signature after confirmation. The designer will sign for Party A, and the other will return the signature to the company to obtain bulk commodities.
4、应提醒公司的打样人员保持样品配方，并避免在生产产品时再次掺杂。
4. The proofing personnel of the company should be reminded to keep the sample formula safe and avoid doping again in the production of products.
二、GRC构件图纸深化确认
2、 GRC component drawing deepening confirmation
设计师应加深良好的图纸，并应由公司图纸主管进行审查。验证正确之后，会将设计者发送给设计者进行审查。甲方确认图纸后，甲方应签字并退还公司。甲方设计者签名和审查的图纸应保存在的地方，如有任何争议，可作为今后的依据。
The designer should deepen the good drawings and should first be reviewed by the company's drawing supervisor. After verification, the designer will be sent to the designer for review. After Party A confirms the drawings, Party A shall sign and return them to the company. The drawings signed and reviewed by the designer of Party A shall be kept in a safe place. If there is any dispute, it can be used as a basis for the future.
三、GRC构件模具制作模具验收
3、 GRC component mold making mold acceptance
山东GRC构件有四种类型的模具。有钢模，玻璃钢模，木模和硅树脂模，并且重复使用率依次降低。钢模由制造商根据图纸生产。当需要使用硅胶模具时，必须使用玻璃纤维增强塑料模具。由于硅树脂模具相对较软，因此需要由FRP模具支撑以保持产品的形状。
There are four types of molds for GRC components in Shandong. There are steel mold, FRP mold, wood mold and silicone mold, and the reuse rate decreases in turn. The steel formwork is produced by professional manufacturers according to the drawings. When silicone mold is needed, glass fiber reinforced plastic mold must be used. Because the silicone mold is relatively soft, it needs to be supported by FRP mold to maintain the shape of the product.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.aswjc.com And consult our staff, will serve you wholeheartedly.
