浮雕材质的不同，其制造工艺流程也存在不同，普通浮雕运用石材、玻璃钢、锻铜这三种材质，在这里我们也就分这三品种型浮雕来分别引见其制造工艺流程：
The manufacturing process of relief is also different with different materials. Ordinary relief uses three materials: stone, FRP and forged copper. Here, we will introduce the manufacturing process of these three types of relief:
一、石材浮雕制造工艺流程
1、 Manufacturing process flow of stone relief
石材是浮雕运用较多的材质，在制造石材浮雕之前，需选择与图稿及设计请求匹配的石材，并检查色差，然后把毛材制造成板材，将其锯解成尺寸料，并停止合缝检查，接着就是按图稿1：1制成大稿。在雕琢大图放制后，接着就是停止石材大形雕琢，再然后由技师精摹细琢。接下来等磨光雕琢全部竣工后，就停止细部处置，并用粗砂布、细砂布停止磨光。然后就是废品验收，等验收完后就要肯定装置尺寸，做好钢材骨架，后就是浮雕整体的装置，然后在由技师停止部分处置，并停止装置验收。
Stone is a material used more in relief. Before manufacturing stone relief, it is necessary to select the stone matching the drawings and design requirements, check the color difference, then manufacture the wool into plates, sawn it into size materials, stop joint inspection, and then make a large draft according to 1:1 of the drawings. After the large-scale carving drawing is made, then the large-scale carving of stone is stopped, and then the technician will carefully copy and carve it. Next, after the polishing and carving are completed, stop the detailed disposal, and stop the polishing with coarse emery cloth and fine emery cloth. Then there is the acceptance of waste products. After the acceptance, it is necessary to confirm the size of the device, do a good job in the steel skeleton, and finally emboss the overall device, and then stop the partial disposal by professional technicians and stop the device acceptance.
二、锻铜浮雕制造工艺流程
2、 Manufacturing process flow of forged copper relief
锻铜浮雕在古代运用较多。而制造锻铜浮雕，同样要先停止1：1的泥稿制造，然后在泥稿的根底上翻制玻璃钢锻模，做完这一步后接下来就是在玻璃钢锻模根底上停止人工锤锻，制造成锻铜浮雕废品，接着就是对锻铜浮雕外表停止打磨处置，并依据图稿作部分着色处置，然后就只剩装置了。
Wrought copper relief was widely used in ancient times. For the manufacture of forged copper relief, it is also necessary to first stop the production of 1:1 clay manuscript, and then turn over the FRP forging die on the basis of the clay manuscript. After this step, the next step is to stop manual hammer forging on the basis of the FRP forging die to produce forged copper relief waste products, and then stop polishing the surface of forged copper relief, and make partial coloring according to the drawings, Then there's only the device left.
三、玻璃钢浮雕制造工艺流程
3、 Manufacturing process flow of FRP relief
玻璃钢材质是近年来开展盛行的雕塑资料，因而现代浮雕运用玻璃钢较多。在制造玻璃钢浮雕之前，要先停止1：1的泥稿制造，然后就是在泥稿的根底上翻制石膏模，并停止精密打磨，再者就是在石膏模的根底上翻制玻璃钢浮雕废品，在翻制玻璃钢浮雕废品后就要对玻璃钢浮雕外表停止打磨，并依据图稿作部分着色处置，在停止完打磨，着色后就是装置了。
FRP is a popular sculpture material in recent years, so FRP is widely used in modern relief. Before making FRP relief, stop making 1:1 clay manuscript, then turn over the gypsum mold on the base of the clay manuscript and stop precision grinding. In addition, turn over the FRP relief waste on the base of the gypsum mold. After turning over the FRP relief waste, stop grinding the surface of the FRP relief, and make partial coloring treatment according to the drawings. After stopping grinding, After coloring, it is the device.
The above information is the knowledge sharing provided by Shandong relief sculpture manufacturer to Xiaobian. For more wonderful contents, please click our website: http://www.aswjc.com We will have more content for you to check later
