GRC构件是一种装饰材料，可以以自由的形式满足设计师各种个性形式的要求，因此受到设计师的青睐，当然，安装的规格也是必要的，以下厂家将教安装济南GRC构件的正确步骤以及质量标准。

GRC component is a kind of decorative material, which can meet the requirements of various personality forms of designers in a free form, so it is favored by designers. Of course, the installation specifications are also necessary. The following manufacturers will teach the correct steps and quality standards for installing GRC components in Jinan.

安装GRC构件的正确步骤

Correct steps for installing GRC components

1.根据图纸在GRC构件安装处放出定位线。

1. Set out the positioning line at the installation of GRC components according to the drawing.

2.然后按照施工图纸的说明安装切割尺寸的GRC构件，切割GRC构件时，如何掌握GRC构件的尺寸，确保线迹的宽度正好。

2. Then install the cut size GRC members according to the instructions of the construction drawings. When cutting GRC members, how to grasp the size of GRC members, first ensure that the width of the stitch is right.

3.粘贴GRC构件时，网眼布可以折叠，也可以直接粘贴。使用性能良好的粘结砂浆，可用薄层密实的方法将砂浆从GRC构件中强制挤出，粘接处用粘接剂固定，宽度小于3mm，保持粘接处牢固清洁。

3. When pasting GRC components, the mesh can be folded or pasted directly. Use the bonding mortar with good performance. The mortar can be forced out of the GRC member by thin layer compaction. The bonding part is fixed with adhesive, with a width of less than 3mm, and the bonding part is kept firm and clean.

4.安装GRC构件，先测量构件的尺寸，现在试着用平地拼接，构件之间的间隙小于3mm时，用性能良好的粘结砂浆粘结，注意粘结砂浆的均匀分布。

4. When installing GRC components, first measure the size of the components, and then try to splice them with flat ground. When the gap between the components is less than 3mm, use the bonding mortar with good performance to bond, and pay attention to the uniform distribution of the bonding mortar.

5.检查拼接好的GRC构件，可用砂纸打磨接缝粘结砂浆。粘结砂浆干燥后，可以使用GRC构件的抗裂橡胶进一步粘结。

5. Check the spliced GRC components and polish the joint bonding mortar with sandpaper. After the bonding mortar is dry, the anti-crack rubber of GRC components can be used for further bonding.

GRC构件安装的质量标准

Quality standard for GRC component installation

1、构件安装要求横平竖直，整体在线，图案完整，曲线光滑，构件表面没有污染，无缺陷。

1. The components shall be installed horizontally and vertically, with the overall line, complete pattern, smooth curve, and no pollution and defect on the surface of the components.

2、正确找好构件的安装节点，防止因预埋件错位导致构件扭曲，长期产生安装应力和变形。

2. Correctly locate the installation nodes of the components to prevent the distortion of the components due to the misplacement of the embedded parts and long-term installation stress and deformation.

3、构件连接点连接无泄漏，请拧紧螺栓后再拧紧。

3. There is no leakage at the connection point of the component. Please tighten the bolts before tightening.

4、构件接缝光滑，接缝小于10毫米

4. The component joint is smooth, and the joint is less than 10mm

5、纵向构件请勿使上部构件与底部构件重叠，但是，各部件请单独安装在墙上。

5. Do not overlap the upper component and the bottom component of the longitudinal component, but install each component separately on the wall.

6、构件安装后，需要自上而下将表面灰尘、污物清扫干净，吊钩间隙应牢固平整。

6. After the installation of components, the surface dust and dirt shall be cleaned from top to bottom, and the hook gap shall be firm and flat.

以上是厂家介绍的安装方法和安装质量标准，能抵抗外界环境的损伤、变形和开裂，使用时应按照正确的安装方法操作；可能会危及人身，导致其他不必要的损失。还有产品事项要了解就来我们网站http://www.aswjc.com咨询！

The above is the installation method and installation quality standard introduced by the manufacturer, which can resist the damage, deformation and cracking of the external environment, and should be operated according to the correct installation method during use; It may endanger personal safety and cause other unnecessary losses. If you need to know more about products, please come to our website http://www.aswjc.com consulting service