As we all know, GRC is a kind of fiber-reinforced concrete composite material with alkali resistant glass fiber as reinforcement material and cement mortar as base material. It is also a decorative cement component for building details, so there must be relevant specifications and requirements for the installation of buildings. Otherwise, improper operation will cause personal safety and other unnecessary losses.

那么接下来小编告诉大家GRC构件正确的安装方法到底是怎样的?

So what is the correct installation method of GRC components?

一定要提醒大家的是，较大GRC构件的重量比较重，容易掉落下来，所以我们可以通过设置支撑的方法进行临时加固，方便进行施工。

First of all, we must remind you that the weight of large GRC components is relatively heavy and easy to fall down, so we can set support method for temporary reinforcement to facilitate construction.

一、GRC构件正确的安装方法:

1、 Correct installation method of GRC components:

1、在待安装GRC构件的部位按照图纸弹出定位线(中线或边线)

1. First, pop out the positioning line (center line or side line) at the position where GRC components are to be installed according to the drawing

2、然后按照施工图纸说明来安装尺寸切割GRC构件。在切割GRC构件时，如何把握GRC构件的大小呢?我们要保证其拼接缝宽恰到好处。

2. Then install the dimension cutting GRC components according to the construction drawing. When cutting GRC components, how to grasp the size of GRC components? First of all, we need to ensure that the splicing joint width is just right.

3、在粘贴GRC构件时，可以对网格布进行翻包，也可以直接粘贴。可以使用粘结砂浆，通过薄层满粘法的方法进行粘贴，可以将砂浆用力的从GRC构件中挤出。其粘接缝应随粘随勾，宽度要小于3毫米，保持粘接缝的饱满和清洁。

3. When pasting GRC components, the grid cloth can be turned over or pasted directly. High quality bonding mortar can be used to paste through thin layer full bonding method, and the mortar can be forced out of GRC members. The gluing joint shall be glued at any time and the width shall be less than 3mm to keep the gluing joint full and clean.

4、进行GRC构件的安装，先测好GRC构件的大小，先在平地上进行试拼接，如果GRC构件之间的缝隙小于3毫米，则可以使用粘结砂浆进行粘结，注意粘结砂浆的分布均匀。

4. For the installation of GRC components, the size of GRC components shall be measured first, and trial splicing shall be carried out on flat ground first. If the gap between GRC components is less than 3mm, high-quality bonding mortar can be used for bonding, and attention shall be paid to the uniform distribution of bonding mortar.

5、检查一下拼接完的GRC构件，可以使用砂纸将接缝处的粘结砂浆打磨干净。在粘结砂浆干燥之后，可以使用GRC构件抗裂专用胶来进行进一步的黏贴。

5. Check the spliced GRC components, and polish the bonding mortar at the joints with sandpaper. After the bonding mortar is dried, GRC component crack resistant adhesive can be used for further bonding.

二、GRC构件安装的质量标准:

2、 Quality standard for GRC component installation:

1、构件安装要求横向平整、竖向垂直、整体上线、花饰组对完整、曲线圆滑流畅，构件表面无污染、缺损。

1. The installation of components requires horizontal flatness, vertical perpendicularity, overall on-line, complete decoration group, smooth and smooth curve, and no pollution and defect on the component surface.

2、构件安装节点对位准确，防止因埋件错位导致构件强扭就位，产生安装应力而日久变形。

2. The installation nodes of the components shall be aligned accurately to prevent the components from being forced to twist in place due to the dislocation of the embedded parts, resulting in the installation stress and long-term deformation.

3、构件连接点必须连接到位，不得遗漏。螺栓连接必须带紧拧靠。

3. The connection points of components must be connected in place without omission. The bolt connection must be tightened.

4、构件接头顺畅，接缝小于10mm。

4. The joint of components shall be smooth, and the joint shall be less than 10 mm.

5、竖向构件应避免将上部构件层层叠压在底部构件上，而应将每一截构件单独悬挂安装在墙体上。

5. Vertical members shall avoid stacking the upper members on the bottom members, and each member shall be hung and installed on the wall separately.

6、构件安装完毕，应自上而下将表面的灰尘和污渍清扫干净，勾缝饱满、打磨平整。

6. After the installation of components, the dust and stains on the surface shall be cleaned from top to bottom, and the joints shall be full and polished.